Genel Bakış

Note that this is the same lens height as the version for the Canon C50, however, this assembly has a shorter thumbscrew and safety button to allow the Nikon battery and memory card to be changed without removing the baseplate.

ARRI dovetail slot on the bottom attaches using a top-load locking mechanism to the included Baseline ARRI Dovetail or other ARRI standard dovetails.

Loosen the thumbscrew and push the silver button on the operator’s side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew.

ARCA dovetail slot on top holds Baseline ARCA Dovetails and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until the ARCA clamp has opened fully. Reverse the process to tighten.

Genel Bakış

Upper Cage for Nikon ZR is a form-fitting cage with 1/4-20, 3/8-16, and M4x20mm ARRI MAP threaded holes in several places.

The swing-away HDMI lock protects the camera’s micro-HDMI port from abuse while allowing the dust cover to be accessed.

The combination battery/CF Express door on the bottom is unobstructed for easy card changes.

Lower ARCA Swiss dovetail has an adjustable lens support clamp with three included lengths of 1/4-20 support screw that attach to 3rd party lens adapters like Metabones, etc.

Genel Bakış

Handle Clamp Cheeseplate (KODAK Super 8) is a cheeseplate that clamps to the front of the camera handle and provides ARRI 3/8-16, 1/4-20, and M4x20mm MAP holes.

Flippable in every direction for multiple mounting options.

Combine with Universal ARRI Hot Shoe (1/4-20 and 3/8-16) and Microphone Shock Mount (Hot Shoe) for a configurable mic holder.

Genel Bakış

Power Distribution Box Hinge Adapter (15mm LW) attaches to the DB-4, DB-9, and DB-11 Power Distribution Boxes to allow them to be mounted on 15mm LW Rods.

The friction rod clamp allows for tilted positioning and adjustment without loosening a thumbscrew.

Genel Bakış

Power Distribution Box DB-13 (FUJIFILM GFX ETERNA 55, V-Mount) attaches directly to the back of the camera body using the V-Mount interface to provide intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable LANC cable enables remote start/stop capability using 3pin Fischer devices.

Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-13 will switch to an onboard battery.

With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the ETERNA uses approximately 2.0A at 14V so when using a 10A capable battery, the remaining 8.0A is allocated for accessory use. If an accessory configuration exceeds the 8.0 limit, accessory power is cut off, leaving the camera powered. The “SMART FUSE” LED will illuminate showing the error and once the configuration has been adjusted to lower than 8.0A, the RESET button can be pressed and power will be re-enabled to accessory outputs.

Genel Bakış

Power Distribution Box DB-4 (Canon C70, V-Mount) attaches to 15mm LW rods with a hinge pivot and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices.

The DB-4 is also compatible with Canon C80.

Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery.

The shoe mount design allows Canon’s BP-A30N battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-4 up and release the battery. Note that the DB-4 provides 19.5V to the camera so that the camera will default to the DC input.

The DB-4 can also be separated from its hinge mount, revealing a 15mm rod clamp with an internal friction sleeve.

With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the C70 uses approximately 1.0A at 14V so when using a 10A capable battery, the remaining 9.0A is allocated for accessory use. If an accessory configuration exceeds the 9.0A limit, accessory power is cut off, leaving the camera powered. The “SMART FUSE” LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 9.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs.

In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.